Exfo CableSHARK P3 VF/DSL Cable Qualifier Instrukcja Użytkownika Strona 35
- Strona / 321
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
CableSHARK P3 User Guide
23
positioned to the inside of the battery compartment. In some CableSHARK’s, this may require some
maneuvering to position the connector in place. The excess battery wire should be carefully inserted into the
side slot of the battery compartment. Install the battery in the compartment; replace the battery cover and
tighten the two slotted screws in place.
Return the old battery to EXFO for recycling. Immediately, (same day) plug the CableSHARK into the mains
so that the battery will be charged. The power LED should be green at this time. Charge the unit until fully
charged.
4.2.3 The LED Power Status Indicator
The CableSHARK’s dual color Power Status LED is designed to indicate the instrument's power status:
State Explanation
Bright Green Running on mains power, the battery is fully charged
Dull Green Running on the battery
Flashing Green The battery is charging
Red The battery is exhausted or there is a malfunction in the battery
Note: The LED can also illuminate so it is orange in colour.
Orange Both the red and green LED’s will illuminate (looks orange) to indicate
the unit is in Responder mode.
- CableSHARK P3 3
- VF / DSL Cable Qualifier 10
- Patent Information 11
- 1.2 Unpacking the CableSHARK 13
- 1000 ft (300 m) 22
- 4.1.1 The Front Panel 27
- 4.1.2 The Rear Panel 29
- 4.2 Powering the CableSHARK 33
- 5.1.1 Self Tests 37
- 5.2.2 Single-Ended Testing 39
- 5.2.3 End-to-End Testing 40
- 5.3.1 Saving Results 41
- 5.3.2 Recalling Results 43
- 5.4 Reference Masks 45
- 5.6 Bandwidth Requirements 50
- Section 6 Main Menu 51
- 6.2 Responder Mode 58
- 6.3 Recall Results 59
- 6.4 The System Setup Menu 59
- 7.2.1 Automatic TDR Test 65
- 7.2.2 Manual TDR Test 66
- 7.3 Frequency Response Tests 67
- 7.4.2 End-to-End DMT Test 69
- 7.5 Noise Tests 70
- 7.7 Load Coil Detection Test 71
- 7.8 Spectral Detective 72
- 7.10 Return Loss 73
- 7.12 4 Wire Xtalk 73
- 7.14 ADSL Auto Test 74
- 7.15 SHDSL Auto Test 75
- 7.16 VF Auto Test 76
- 7.17 Ground Resistance Test 77
- 7.19 K-Test 78
- 7.20 Ringer Detection 79
- 7.21 VF Tests 79
- 7.22 LoopMapper™ Tests 79
- CableSHARK 81
- FREQUENCY RESPONSE TEST SETUP 84
- 8.2.1 Setting up a TDR Test 89
- 8.2.2 Manual TDR Testing 95
- 8.2.3 Auto TDR Testing 101
- 8.2.4 TDR Application Hints 102
- CableSHARK P3 User Guide 103
- 8.3.1 Setting up a DMT Test 105
- DMT BITS PER 107
- (m/μS): 108
- 8.3.2 Running an ADSL Test 110
- DMT TEST RESULT 114
- 8.4..Noise Measurements 118
- 8.4.2 Running a Noise Test 124
- 00:00:00 125
- TO MEM 130
- TO USB 135
- 8.7.1 Setting up a DMM Test 142
- 8.7.2 Running a DMM Test 148
- 8.8.. 4-Wire Crosstalk Test 151
- 17.3 kHz to 2.208 MHz) 155
- > 100 M 157
- 8.10 LoopMapper™ 159
- 8.10.2 LoopMapper Testing 161
- 8.11.1 Auto Test Setup 168
- IGURE 8.11.1.3C – PHONE BOOK 174
- Central Office 185
- Customer 185
- IGURE 9.2D – ADSL AT CO SIDE 191
- 11.1..Running a SHDSL Test 199
- IGURE 12.1C – BATTERY CROSS 201
- IGURE 12.1.1.3A – RFL CABLE 203
- Black Red Green 204
- Yel low Blue Green 204
- Black Red Gnd 208
- 12.2 Running a RFL Test 210
- 12.3 RFL Hints 212
- + [ 0.0022 * ( T 213
- - 68°F ) * R 213
- - 20°C ) * 0.00393 * R 214
- Line card = not detected 222
- 15.1.3 Sending 3 Tone Slope 233
- 15.2.3 RX 3 Tone Slope 240
- 15.3 Noise Test 243
- 15.4 Impulse Noise Test 245
- 00:09:12 246
- 15.5 Power Influence 247
- SAVE/UPLOAD button 248
- 16.2 Setting up a K-test 249
- 16.3 Running the K-test 250
- 16.3.3 Running a Test 256
- A.1 Loop Topologies 259
- A.2 Attenuation Responses 261
- Transmitter Characteristics 272
- Transmitter Functions 272
- ± 50 ppm 275
- ± 1.0 dB typical 275
- ± 0.5 dB 277
- SHDSL Data Rate Test 278
- PSD Noise Measurement 278
- Longitudinal Balance Test 279
- DMM (Digital Multimeter) 279
- Isolation resistance 280
- Spectral Detective 280
- 4-Wire Crosstalk 280
- Visi-SHARK 282
- Appendix D Safety 283
- Appendix E Warranty 287
- Certification 288
- F.1 Software Policy 289
- F.2 Upgrading Software 289
- J.1 Installing the Software 295
- J.3.1 Running Visi-SHARK 296
- IGURE J.4.2B – SOCKET ERROR 301
- J.6.1 File Menu 305
- J.6.2 Screen Image menu 307
- J.6.3 New Connection Menu 310
- J.6.4 View Menu 311
- J.6.5 Window Menu 311
- Telecom Test and Measurement 321
Powiązane produkty i podręczniki dla Urządzenia pomiarowe Exfo CableSHARK P3 VF/DSL Cable Qualifier
Urządzenia pomiarowe Exfo FIP-400 Fiber Inspection Probe and ConnectorMax Instrukcja Użytkownika
(78 strony)
(78 strony)
Urządzenia pomiarowe Exfo FIP-400B Fiber Inspection Probe Multifiber Instrukcja Użytkownika
(2 strony)
(2 strony)
Urządzenia pomiarowe Exfo FIP-400B Fiber Inspection Probe Multifiber Instrukcja Użytkownika
(2 strony)
(2 strony)
Urządzenia pomiarowe Exfo FIP-400B Fiber Inspection Probe Multifiber Instrukcja Użytkownika
(2 strony)
(2 strony)
Urządzenia pomiarowe Exfo FIP-400B Fiber Inspection Probe Multifiber Instrukcja Użytkownika
(2 strony)
(2 strony)
Urządzenia pomiarowe Exfo FIP-400B Fiber Inspection Probe and ConnectorMax2 Instrukcja Użytkownika
(111 strony)
(111 strony)
Urządzenia pomiarowe Exfo FIP-400B Fiber Inspection Probe and ConnectorMax2 Instrukcja Użytkownika
(103 strony)
(103 strony)
© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.059 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji