Exfo CableSHARK P3 VF/DSL Cable Qualifier Instrukcja Użytkownika Strona 31
- Strona / 321
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
CableSHARK P3 User Guide
19
PIN MNEMONIC DIRECTION DESCRIPTION
1 N.C. ----- Not Connected
2 RD TO CableSHARK RECEIVED DATA
3 TD FROM CableSHARK TRANSMITTED DATA
4 DTR FROM CableSHARK DATA TERMINAL READY
5 SG COMMON SIGNAL GROUND
6 DSR TO CableSHARK DATA SET READY
7 RTS FROM CableSHARK REQUEST TO SEND
8 CTS TO CableSHARK CLEAR TO SEND
9 N.C. ----- Not Connected
2
3
4
5
6
7
8
2
3
4
5
6
7
8
2
3
4
5
6
7
8
2
3
4
5
6
7
8
Terminal
End
CableSHARK
End
Adapter Connectio
n
Figure 4.1.3A - Serial Interface Connection
The connector is configured as a DTE (Data Terminal Equipment). It is recommended that the cable length
be 50 feet or less to reduce the possibility of errors from signal distortion. Also, the connectors should be
secured with the proper screws to enable reliable operation. All necessary serial cables should be double
shielded where appropriate.
If the unit is connected to a terminal or computer, a Null Modem cable is required. This null modem cable is
available from EXFO and should be ordered with the CableSHARK. Null modem cables are available in
various configurations. The configuration on Figure 4.1.3A above gives the pin arrangement of a typical null
modem cable.
4.1.4 The Ethernet 10BaseT Connection
The Ethernet 10BaseT port is used to connect the CableSHARK to a PC terminal via a LAN or the Internet.
The connector for this is a female RJ-45 connector on the rear panel of the CableSHARK. When connecting
to your equipment, a crossover cable or straight cable can be used (defined below) depending upon the
network infrastructure. The Ethernet interface is compatible with the TIA/EIA T568A and TIA/EIA T568B
specifications. The pin assignments for this are as follows:
- CableSHARK P3 3
- VF / DSL Cable Qualifier 10
- Patent Information 11
- 1.2 Unpacking the CableSHARK 13
- 1000 ft (300 m) 22
- 4.1.1 The Front Panel 27
- 4.1.2 The Rear Panel 29
- 4.2 Powering the CableSHARK 33
- 5.1.1 Self Tests 37
- 5.2.2 Single-Ended Testing 39
- 5.2.3 End-to-End Testing 40
- 5.3.1 Saving Results 41
- 5.3.2 Recalling Results 43
- 5.4 Reference Masks 45
- 5.6 Bandwidth Requirements 50
- Section 6 Main Menu 51
- 6.2 Responder Mode 58
- 6.3 Recall Results 59
- 6.4 The System Setup Menu 59
- 7.2.1 Automatic TDR Test 65
- 7.2.2 Manual TDR Test 66
- 7.3 Frequency Response Tests 67
- 7.4.2 End-to-End DMT Test 69
- 7.5 Noise Tests 70
- 7.7 Load Coil Detection Test 71
- 7.8 Spectral Detective 72
- 7.10 Return Loss 73
- 7.12 4 Wire Xtalk 73
- 7.14 ADSL Auto Test 74
- 7.15 SHDSL Auto Test 75
- 7.16 VF Auto Test 76
- 7.17 Ground Resistance Test 77
- 7.19 K-Test 78
- 7.20 Ringer Detection 79
- 7.21 VF Tests 79
- 7.22 LoopMapper™ Tests 79
- CableSHARK 81
- FREQUENCY RESPONSE TEST SETUP 84
- 8.2.1 Setting up a TDR Test 89
- 8.2.2 Manual TDR Testing 95
- 8.2.3 Auto TDR Testing 101
- 8.2.4 TDR Application Hints 102
- CableSHARK P3 User Guide 103
- 8.3.1 Setting up a DMT Test 105
- DMT BITS PER 107
- (m/μS): 108
- 8.3.2 Running an ADSL Test 110
- DMT TEST RESULT 114
- 8.4..Noise Measurements 118
- 8.4.2 Running a Noise Test 124
- 00:00:00 125
- TO MEM 130
- TO USB 135
- 8.7.1 Setting up a DMM Test 142
- 8.7.2 Running a DMM Test 148
- 8.8.. 4-Wire Crosstalk Test 151
- 17.3 kHz to 2.208 MHz) 155
- > 100 M 157
- 8.10 LoopMapper™ 159
- 8.10.2 LoopMapper Testing 161
- 8.11.1 Auto Test Setup 168
- IGURE 8.11.1.3C – PHONE BOOK 174
- Central Office 185
- Customer 185
- IGURE 9.2D – ADSL AT CO SIDE 191
- 11.1..Running a SHDSL Test 199
- IGURE 12.1C – BATTERY CROSS 201
- IGURE 12.1.1.3A – RFL CABLE 203
- Black Red Green 204
- Yel low Blue Green 204
- Black Red Gnd 208
- 12.2 Running a RFL Test 210
- 12.3 RFL Hints 212
- + [ 0.0022 * ( T 213
- - 68°F ) * R 213
- - 20°C ) * 0.00393 * R 214
- Line card = not detected 222
- 15.1.3 Sending 3 Tone Slope 233
- 15.2.3 RX 3 Tone Slope 240
- 15.3 Noise Test 243
- 15.4 Impulse Noise Test 245
- 00:09:12 246
- 15.5 Power Influence 247
- SAVE/UPLOAD button 248
- 16.2 Setting up a K-test 249
- 16.3 Running the K-test 250
- 16.3.3 Running a Test 256
- A.1 Loop Topologies 259
- A.2 Attenuation Responses 261
- Transmitter Characteristics 272
- Transmitter Functions 272
- ± 50 ppm 275
- ± 1.0 dB typical 275
- ± 0.5 dB 277
- SHDSL Data Rate Test 278
- PSD Noise Measurement 278
- Longitudinal Balance Test 279
- DMM (Digital Multimeter) 279
- Isolation resistance 280
- Spectral Detective 280
- 4-Wire Crosstalk 280
- Visi-SHARK 282
- Appendix D Safety 283
- Appendix E Warranty 287
- Certification 288
- F.1 Software Policy 289
- F.2 Upgrading Software 289
- J.1 Installing the Software 295
- J.3.1 Running Visi-SHARK 296
- IGURE J.4.2B – SOCKET ERROR 301
- J.6.1 File Menu 305
- J.6.2 Screen Image menu 307
- J.6.3 New Connection Menu 310
- J.6.4 View Menu 311
- J.6.5 Window Menu 311
- Telecom Test and Measurement 321
Powiązane produkty i podręczniki dla Urządzenia pomiarowe Exfo CableSHARK P3 VF/DSL Cable Qualifier
Urządzenia pomiarowe Exfo FIP-400 Fiber Inspection Probe and ConnectorMax Instrukcja Użytkownika
(78 strony)
(78 strony)
Urządzenia pomiarowe Exfo FIP-400B Fiber Inspection Probe Multifiber Instrukcja Użytkownika
(2 strony)
(2 strony)
Urządzenia pomiarowe Exfo FIP-400B Fiber Inspection Probe Multifiber Instrukcja Użytkownika
(2 strony)
(2 strony)
Urządzenia pomiarowe Exfo FIP-400B Fiber Inspection Probe Multifiber Instrukcja Użytkownika
(2 strony)
(2 strony)
Urządzenia pomiarowe Exfo FIP-400B Fiber Inspection Probe Multifiber Instrukcja Użytkownika
(2 strony)
(2 strony)
Urządzenia pomiarowe Exfo FIP-400B Fiber Inspection Probe and ConnectorMax2 Instrukcja Użytkownika
(111 strony)
(111 strony)
Urządzenia pomiarowe Exfo FIP-400B Fiber Inspection Probe and ConnectorMax2 Instrukcja Użytkownika
(103 strony)
(103 strony)
© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.093 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji