Exfo FTB-8500 Series for FTB-200 Instrukcja Użytkownika Strona 219
- Strona / 513
- Spis treści
- ROZWIĄZYWANIE PROBLEMÓW
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
Stream Generation Tabs
Ethernet and Fibre Channel Application 205
Overview
Rate: Indicates the stream rate. The rate is calculated according to the
configured traffic shaping (from Transmit Mode and TX Rate fields on
page 217).
Enable: Allows enabling the corresponding stream. However, the
stream will be generated only when the Enable TX - On/Off button is
at the On position when the test is started.
Note: The Individual stream can be enabled/disabled even when the test is
started and running. The streams can be enabled one after the other, up to
10, as long as the maximum rate is not reached. For example, if the first
stream is using the full rate available, then no other stream can be enabled.
However, if the first enabled stream uses half rate, then at least another
stream can be enabled using up to half rate. Thus, to enable a second
stream, first set the Maximum or TX rate value within the non-used rate,
then enable it. A stream cannot be enabled if its MAC address is not valid, it
can be either not resolved or wrongly entered.
Total Enabled TX Rate: Displays the total enabled rate that will be
generated by the selected streams.
Total Available TX Rate: Displays the total rate available for traffic
generation.
Unit choices are %, bps, Kbps, Mbps, Gbps, Bps, KBps, MBps, and
GBps. The default setting is %.
- Ethernet and 1
- Fibre Channel Application 1
- Contents 3
- Certification Information 9
- CE Declaration of Conformity 11
- DECLARATION OF CONFORMITY 12
- IMPORTANT 17
- 2 Safety Information 19
- 3 Getting Started 23
- FTB-8510B Model 25
- LED Status Description 26
- 1x/2x Fibre Channel 27
- LEDs for Optical Ports 28
- FTB-8510G Model 29
- FTB-8525 and FTB-8535 Models 31
- Ethernet 100/1000 Mbps 33
- 1x/2x/4x Fibre Channel 41
- 5 Introducing the Smart User 47
- Main Window 49
- Main Menu 50
- Print Screen 52
- Global Test Status 55
- Test Controls 56
- Button Description 57
- Favorites 58
- Factory Default 59
- Test Report Generation 60
- Configuration 64
- Typical Tab Elements 67
- Alarm/Error Measurements 68
- Arrow Buttons 68
- Table Sorting 69
- Port Selection 69
- Keyboard Usage 70
- (0 through 9 and A through F) 73
- For MAC address 73
- For IPv6 address 73
- 6 Creating and Starting a 77
- Test Case 77
- Introducing the Test Setup 78
- Available with 79
- Test Case Availability 80
- EtherSAM (Y.1564) Test Case 81
- Test Set Test Cases 87
- IPv4 IPv6 92
- Ethernet RFC 2544 Test Case 95
- Ethernet BERT Test Case 100
- Fibre Channel BERT Test Case 118
- 7 Summary Tabs 123
- Test Status 124
- Test Configuration 126
- Clock Configuration 127
- Timer Configuration 128
- Alarm Analysis 129
- Alarm Summary 130
- for all interfaces 131
- Test Preferences 133
- Test Logger 134
- Logger Table 135
- Test L ogger 136
- View/Hide Details 137
- Log Details 138
- 8 I/F Setup Tabs 139
- Port Setup 140
- Flow Control 141
- Network Setup 143
- IP Configuration 144
- Advanced Auto-Neg. TX 146
- Configuration 147
- Auto-Neg. Fault Register 149
- Enable Local Capabilities 149
- Local Capabilities 149
- Negotiate Button 150
- Advanced Auto-Neg. RX 151
- Apply to Port Configuration 152
- Link Partner Capabilities 152
- Interface 153
- Buffer-to-Buffer Flow Control 156
- World Wide Name 156
- 9Port Tabs 157
- Electrical TX 158
- Frequency 159
- Electrical RX 160
- Frequency Analysis 161
- Optical TX 162
- Optical RX 164
- 10 WIS Tabs 167
- Alarm Generation 168
- Error Injection 169
- Path Signal Label (C2) 170
- J0 Trace 170
- J1 Trace 170
- Error Analysis 171
- WIS OH RX 174
- Section Overhead 175
- Line Overhead 175
- Path Overhead 176
- 11 Traffic Analyzer Tabs 177
- Ethernet TX 178
- PHY Error Injection 179
- MAC Error Injection 179
- Ethernet RX 181
- Errors Analysis 182
- Ethernet Statistics 184
- Valid Frame Counts 185
- Frame Size 186
- Throughput 186
- Valid PBB-TE Frame Counts 187
- PPB-TE Frame Size 188
- PBB-TE RX Throughput 188
- Higher Layers 189
- Flow Control 191
- Destination MAC Address 192
- Statistics 193
- Traffic Filters 194
- Enabled Time 195
- Frame Count 195
- Traffic Filter Configuration 196
- Filter Configuration 198
- Configure Button 199
- Category Filter Comment 200
- Frame Length 204
- Status and Controls 206
- Traffic Analyzer Tabs 208
- FC Error Injection 211
- FC Latency 214
- Latency Measurements 215
- Buffer-to-Buffer Credit 215
- FC Statistics 216
- 12 Stream Generation Tabs 217
- Overview 218
- FTB-8510G 221
- Component Description 224
- Stream Configuration 225
- Frame Configuration 226
- Traffic Shaping 231
- Stream No 234
- Destination 235
- Frame Format 236
- MPLS Configuration 240
- IP/UDP/TCP 241
- Frame Delimiters 245
- EOF Description 246
- Frame Parameter 247
- FC Header 248
- D_ID Description 249
- Bit Field Description 251
- 2 Exchange 252
- 13 Stream Analyzer Tabs 255
- RX Frame Count 257
- Stream Errors Analysis 257
- Round Trip Latency 258
- 14 Pattern Tabs 259
- Pattern TX 260
- Pattern RX 263
- 15 RFC 2544 Tabs 265
- Global Configuration 266
- Test Procedure 268
- Latency Measurement 269
- Throughput Configuration 270
- Back-to-Back Configuration 273
- Frame Loss Configuration 275
- Latency Configuration 277
- Throughput Results 280
- Back-to-Back Results 282
- Frame Loss Results 284
- Latency Results 286
- 16 EtherSAM Tabs 293
- Overview (Configuration) 294
- Burst Test 296
- Performance Test 296
- Sub-Tests Duration 297
- Total TX Rate (%) 298
- Services (Configuration) 299
- Direction 300
- Frame Parameters 300
- SLA Parameters 301
- Test Parameters 304
- Ramp (Configuration) 305
- Step List 306
- Step Time 306
- Ramp Duration 306
- Burst (Configuration) 307
- Parameters 308
- Global Progress and Alarms 310
- Configuration Test Overview 312
- Performance Test Overview 314
- Configuration Test (Results) 316
- Ramp and Burst Tests Table 317
- Performance Test (Results) 319
- Sequence Tracking 320
- One-Way Latency 321
- 17 TCP Throughput Tabs 323
- TCP Mode 324
- TCP Connection Configuration 324
- TCP Connection Status 325
- TCP Throughput Configuration 326
- TCP Throughput Results 327
- TCP Statistics 328
- 18 Advanced Tab 329
- Service Disruption Time (SDT) 332
- 19 Common Tab 333
- Standard 334
- Performance Monitoring (PM) 336
- 20 Expert Mode Tabs 337
- Expert Mode (RFC 2544) 338
- Expert Mode Status 339
- Throughput (RFC 2544) 340
- Back-to-Back (RFC 2544) 342
- Frame Loss (RFC 2544) 344
- Latency (RFC 2544) 346
- Expert Mode (BERT) 348
- Port (BERT) 349
- Ethernet (BERT) 351
- Pattern (BERT) 353
- 21 System Tabs 355
- Application Preferences 356
- Audible Error/Alarm 357
- FTB-8120NGE/FTB-8130NGE 358
- FTB-8510B 358
- Interface Configuration 359
- IPv6 Test Preferences 361
- FC Test Preferences 364
- Versions 366
- Information 367
- Software Options 369
- Available Options 370
- Category Name Description 371
- Clock Synchronization 374
- Clock Out 377
- 22 Tools Tabs 379
- IPv6IPv4 381
- Trace Route 386
- Status Description 388
- ENIU Configuration 390
- ADC Configuration 391
- Selected ENIU 393
- Loopback 394
- 802.3ah Configuration 395
- OAM Discovery Statistics 397
- 802.3ah Statistics 398
- 802.3ah Events 401
- Traffic Scan 403
- Mode Level Description 404
- Monitored Frames Table 406
- Tools Tabs 407
- Filter Cfg 409
- 23 Suspend and Resume 411
- Resume Operation 412
- 24 Power Failure Recovery 413
- When Using SmartMode 414
- 25 Maintenance 415
- Recalibrating the Unit 416
- Recycling and Disposal 416
- 26 Troubleshooting 417
- Transportation 418
- 27 Warranty 419
- Liability 420
- Service and Repairs 422
- ASpecifications 425
- Ethernet Optical Interfaces 426
- Fibre Channel Interfaces 428
- ELECTRICAL INTERFACES 430
- Ethernet Cables 431
- Specifications 432
- Crossover Cable (1000 Mbps) 432
- Synchronization Interfaces 433
- B Glossary 435
- Acronym List 436
- VLAN/B-VLAN 448
- MPLS Labels 449
- Path Signal Label (C2 byte) 450
- C Pop-Up Windows 451
- VLAN Configuration 452
- B-MAC Destination Address: 453
- IPv4 Configuration 455
- IPv6 Address Configuration 457
- Global IPv6 Address 458
- Mode Status Description 459
- Default Gateway Address 460
- Destination IPv6 Address 461
- Service Profile Configuration 463
- Framing Configuration 464
- Frame Size Configuration 465
- Frame Format Configuration 467
- MAC Configuration 468
- UDP Configuration 470
- TCP Configuration 470
- Advanced TOS/DS 471
- Advanced Ping 474
- Advanced Trace Route 476
- Filter Selection 477
- Truncation Calculator 478
- Field Match Configuration 479
- Triggered Frame Details 481
- Data Capture Export 482
- D Report Generator 485
- Report Generator Installation 486
- Model Application Folder 488
- Error message 490
- Sections 492
- View Report After Generation 493
- Default Button 493
- Generate Button 493
- Close Button 493
- 147, 151 503
- I/F Setup37 508
- ₼⦌␂ℝ☀⹂䓸德棟Ⓟ䤓屓⸩ 511
- MARKING REQUIREMENTS 512
Powiązane produkty i podręczniki dla Urządzenia pomiarowe Exfo FTB-8500 Series for FTB-200
(574 strony)
Urządzenia pomiarowe Exfo FTB/IQS-85100G Packet Blazer for FTB-500/IQS-600 Instrukcja Użytkownika
(448 strony)
(448 strony)
Urządzenia pomiarowe Exfo FTB/IQS-88000 Series Power Blazer for FTB-2/2Pro/5 Instrukcja Użytkownika
(681 strony)
(681 strony)
Urządzenia pomiarowe Exfo FastReporter Data Post-Processing Software Instrukcja Użytkownika
(256 strony)
(256 strony)
Urządzenia pomiarowe Exfo FastReporter Data Post-Processing Software Instrukcja Użytkownika
(270 strony)
(270 strony)
(274 strony)
(47 strony)Opticon 12754 Handbücher
Bedienungsanleitungen und Benutzerhandbücher für Handheld-Mobilcomputer Opticon 12754.
Wir stellen 1 PDF-Handbücher Opticon 12754 zum kostenlosen herunterladen nach Dokumenttypen zur Verfügung Datenblatt
Komentarze do niniejszej Instrukcji